Most popular dual-cab utes in Australia advertise a 3500 kg braked towing capacity, so it’s easy to assume any of them can pull a fully loaded 3.5 tonne plant trailer. The towing capacity is only one of several limits, though, and on many utes it isn’t the one that runs out first. Here’s what to check before you hook up.
This article is general information only. Always check your vehicle owner’s manual, towbar plate and your state’s road authority for the limits that apply to your vehicle.
The four numbers that matter
1. Braked towing capacity
The maximum the trailer and its load may weigh when the trailer has its own brakes. All our Vlemmix plant trailers are braked trailers. The actual loaded weight of the trailer must stay within this figure – and within the rating of your towbar, which can be lower than the vehicle’s.
2. Maximum tow ball load
The downward weight the trailer puts on your towbar. Utes rated to tow 3500 kg typically allow around 350 kg on the ball, but check your vehicle and towbar plate. A common guide (used by WA’s Department of Transport among others) is a tow ball load of roughly 8–10% of the loaded trailer’s weight, never exceeding the vehicle or towbar maximum. Too little ball weight can make the trailer sway; too much overloads the rear of the ute.
3. GVM (Gross Vehicle Mass)
The maximum your ute may weigh when loaded – and the weight on the tow ball counts towards it, along with passengers, fuel, tools and accessories like a canopy or bull bar.
4. GCM (Gross Combination Mass)
The maximum the loaded ute plus the loaded trailer may weigh together. This is the one that catches people out.
Why GCM is the real limit
Take a typical ute with a GCM of 6000 kg and a 3500 kg towing capacity. If you tow the full 3500 kg, the ute itself – including you, fuel, tools and the tow ball load – can only weigh 2500 kg. Many dual-cab utes weigh well over 2000 kg empty, so there may be very little left for people and gear.
Some newer models have improved this. Toyota, for example, lifted the GCM of the 2026 4×4 HiLux to 6300 kg, which carsales reported leaves an SR5 dual-cab automatic with around 615 kg of payload when towing 3500 kg – up from about 240 kg before. Other models leave far less. Look up the GCM for your exact model, not just the towing capacity.
Motoring writers also commonly suggest staying at around 85% of the rated towing capacity – about 3 tonnes for a 3500 kg-rated ute – for a comfortable margin, particularly on long or hilly trips.
How a light trailer helps
Every kilo the trailer weighs empty is a kilo of your towing limit you can’t use for your machine. Our Vlemmix plant trailers are built in the Netherlands with low tare weights – 700 kg for the 3m Trailer, 770 kg for the 4m Trailer and 900 kg for the 4m 3-Axle Trailer.
Example: a 3m trailer (700 kg) carrying a 1.7 t excavator with a tilt hitch and two buckets (about 2000 kg) weighs around 2700 kg loaded. That’s comfortably inside a 3500 kg towing capacity and leaves more GCM headroom for your ute than towing at the full 3.5 tonnes.
A quick pre-trip checklist
- Know the real loaded weight of the trailer – machine, attachments, chains and all. A public weighbridge removes the guesswork.
- Check it against your vehicle’s braked towing capacity and your towbar rating.
- Position the machine so its weight sits just ahead of the trailer axles, then check the tow ball load is within the vehicle and towbar limit.
- Add up what’s in the ute (people, fuel, tools, accessories, tow ball load) and check it’s under GVM.
- Add the loaded ute and loaded trailer together and check it’s under GCM.
- Secure the machine with rated chains or straps at the trailer’s tie-down points, with the bucket lowered to the deck.
Not sure your ute is up to it?
Send us your vehicle make and model and the machine you want to carry, and we’ll help you choose the lightest trailer that does the job. Start with our guide to choosing the right plant trailer size for your mini excavator, or request a quote and call us on (02) 9119 2914.